First open energy monitor project (part 4)

Submitted by mike_86 on Sat, 07/02/2015 - 15:08

I can't add new posts on the discussion first open energy project part 2

Paul, Surely something is wrong, see this:

pi@raspberrypi ~/RFM2Pi/firmware/RFM69CW_RF_Demo_ATmega328 $ avrdude -v -c arduino -p ATMEGA328P -P /dev/ttyAMA0 -b 38400 -U flash:w:RFM69CW_RF_Demo_ATmega328.cpp.hex

System wide configuration file is "/etc/avrdude.conf"
User configuration file is "/root/.avrduderc"
User configuration file does not exist or is not a regular file, skipping

Using Port : /dev/ttyAMA0
Using Programmer : arduino
Overriding Baud Rate : 38400
avrdude-original: Using autoreset DTR on GPIO 4
AVR Part : ATMEGA328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00

Programmer Type : Arduino
Description : Arduino
Hardware Version: 3
Firmware Version: 4.4
Vtarget : 0.3 V
Varef : 0.3 V
Oscillator : 28.800 kHz
SCK period : 3.3 us

avrdude-original: AVR device initialized and ready to accept instructions

Reading | | 0% 0.0Reading | ################################################## | 100% 0.02s

avrdude-original: Device signature = 0x1e950f
avrdude-original: safemode: lfuse reads as 0
avrdude-original: safemode: hfuse reads as 0
avrdude-original: safemode: efuse reads as 0
avrdude-original: NOTE: FLASH memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude-original: erasing chip
avrdude-original: reading input file "RFM69CW_RF_Demo_ATmega328.cpp.hex"
avrdude-original: error opening RFM69CW_RF_Demo_ATmega328.cpp.hex: No such file or directory
avrdude-original: input file RFM69CW_RF_Demo_ATmega328.cpp.hex auto detected as invalid format
avrdude-original: can't open input file RFM69CW_RF_Demo_ATmega328.cpp.hex: No such file or directory
avrdude-original: read from file 'RFM69CW_RF_Demo_ATmega328.cpp.hex' failed

avrdude-original: safemode: lfuse reads as 0
avrdude-original: safemode: hfuse reads as 0
avrdude-original: safemode: efuse reads as 0
avrdude-original: safemode: Fuses OK
pi@raspberrypi ~/RFM2Pi/firmware/RFM69CW_RF_Demo_ATmega328 $ sudo service emonhub start
[....] Starting OpenEnergyMonitor emonHub: emonhub has been started o[.ok

Re: First open energy monitor project (part 4)

Submitted by pb66 on Sat, 07/02/2015 - 15:32.

On closer examination I can see the firmware repo actuallyhas a slightly different name on the folder to the files. the "12" is missing from the last line so the command should be

avrdude -v -c arduino -p ATMEGA328P -P /dev/ttyAMA0 -b 38400 -U flash:w:RFM69CW_RF12_Demo_ATmega328.cpp.hex

Also when you say you cannot post to the previous threads can you expand on that? Are you getting any error messages? what actually happens when you try to post?

Re: First open energy monitor project (part 4)

Submitted by mike_86 on Sat, 07/02/2015 - 15:53.

When I click on save , message don't appear

Re: First open energy monitor project (part 4)

Submitted by Robert Wall on Sat, 07/02/2015 - 16:01.

You need to look at the message that appears at the top of the thread when you submit your message. You have multiple copies in the queue waiting for moderation. Now one of us has to go through them all and delete the duplicates. Please be a little more patient.

Archived Forum